How To Use QuickPwn 1.1 To Jailbreak iPhone & iPhone 3G 2.1 Guide

These are step by step instructions on how to use QuickPwn 1.1 for Apple Mac OSX to jailbreak your 2.1 iPhone or iPhone 3G.


Step One
Create a folder on your desktop called Pwnage

Step Two
Download QuickPwn 1.1 from here and place it in the Pwnage folder. Likewise, download the latest 2.1 firmware from below and place it in the same folder.

iPhone 2.1 ipsw Download
iPhone 3G 2.1 ipsw Download

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide1-300x183.png


Step Three
Now double click to mount the QuickPwn [QuickPwn_1.1.dmg] archive that you downloaded above. Then drag the QuickPwn application into the Pwnage folder you created on your desktop.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide2-300x206.png

Step Four
Now double click the icon to launch QuickPwn from your Pwnage folder.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide3.png

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide4-300x183.png

Step Five
Click OK to accept the copyright notice.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide5-300x154.png

Step Six
Connect your iPhone or iPhone 3G into the computer when asked, then click OK.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide6-300x129.png

Step Seven
QuickPwn will now automatically detect the device that you connected!

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide7-300x267.png

Step Eight
QuickPwn will now attempt to find the latest firmware for this device

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide8-300x267.png

Step Nine
You will be asked if you would like to replace the original boot and recovery logos on your iPhone. Select Yes or No to continue.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide9-300x131.png

Step Ten
QuickPwn will now build your custom IPSW.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide10-300x267.png

Step Eleven
You will be prompted to enter your username and password. After doing this, then click OK.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide11-300x190.png

Step Twelve
QuickPwn will now guide you on how to put your iPhone into DFU mode. Pay attention and do exactly as QuickPwn directs you. First, turn off the device.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide12-300x267.png

Next, you will be prompted to hold both the Home and Power buttons for 10 seconds.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide13-300x267.png

Finally, you will let go of the power button and continue holding down the Home button for another 10 seconds.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide14-300x267.png

Step Thirteen
QuickPwn will now begin sending information to your iPhone.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide15-300x267.png

Step Fourteen
You will notified that QuickPwn is modifying your iPhone. The process will take some time and will cause the iPhone to reboot. Do not do anything until the process has completed.

http://www.iphone-hacks.com/wp-content/uploads/2008/09/quickpwn-guide16-300x153.png

Step Fifteen
After your iPhone has rebooted it will be jailbroken and have both Cydia and Installer on the Springboard. Congratulations!

0 comments:

Post a Comment

Widget By Devils Workshop